Devices You Need to Install a New Bathtub
Devices You Need to Install a New Bathtub
Blog Article
They are making a few good pointers related to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in this content in the next paragraphs.
Installing a bath tub isn't exactly brain surgery, however it does require solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bath tub with a new one is likewise a reasonably challenging project. If the old tub is readily obtainable, the job can move easily; if you have to open a wall surface to remove the old bathtub and position the brand-new bathtub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will certainly require a helper to vacate the old tub and embeded in the brand-new one. Make certain you have actually certified on your own for the task and fit trying it. Instead of hiring a contractor to take control of a halfway-completed job, it is better to take into consideration utilizing one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This article will aid you install a new bath tub in your bathroom if you have currently acquired a new tub as well as do not require to change the arrangement of your previous water system pipes.
Your devices and also material list should make up the following:
Planning for the Installation
First of all, the sustaining framework provided with the bathroom ought to be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets unit to prevent stress on the tub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you utilize every one of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final position.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain pipes any kind of water staying in the system. The procedure of eliminating the existing taps can be quite problematic due to the restricted accessibility that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a cloth all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have actually been eliminated, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any kind of old sealing compound.
Prior to carrying on to fit the new faucets, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Mounting the Tub
Using both wooden boards under its feet, place the bath tub in the needed position. The wood boards are practical in evenly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 little points.
The following goal is to make certain that the tub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the tub till the spirit level reads degree.
To install faucets, fit the bottom of the outermost versatile faucet port to the appropriate supply pipeline by making a compression join; after that do the same for the various other tap.
Activate the supply of water and also check all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill up the bath tub and likewise examine the overflow outlet as well as the regular outlet for leakages.
Ultimately, fix the bathroom paneling as defined in the producer's user's manual. Tiling and also sealing around the tub needs to wait until the tub has actually been made use of at least when as this will certainly resolve it into its final placement.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end offers a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin making sure that the washing machines remain in place between the tap as well as the sink. Protect the faucet in position with the supplier provided backnut. As soon as the tap is securely in place, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The previous kind should be connected to the tap ends first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall surface in between the bathroom and also the tiling, causing issues with moisture as well as possible leaks to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures and installations. They are marketed in tubes and also cartridges, as well as are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with twists of soaked paper or soft rope. Bear in mind to always load the tub with water before sealing, to allow for the activity experienced when the bathtub remains in use. The sealant can fracture rather very early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also easily readily available on the marketplace. It is recommended to fit the tiles making use of water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were shown that write-up on Installing A Bathtub from a friend on another web blog. Enjoyed our blog posting? Please share it. Help somebody else discover it. I am grateful for your time. Don't hesitate to visit our blog back soon.
Schedule Now!
Report this page